WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS
FEATURES:
- Repairs leak in 30 minutes
- Applicable to pipes up to 18″ (457 mm) diameter
- Applicable on any metal or non-metal pipes
- Repairs T-joint, elbow joint, valve thread, valve body
- Withstand pressure up to 400 psi (28 kg/cm2)
- Withstand temperature up to 200 °C (392 °F)
- Safe for drinking water and resistant to most chemicals
- Reinforce and strengthen pipe after repair
- Permanent repair and extend service life of pipes
PACKAGE:
1 roll of Wrap Seal Fiberglass Tape | ||
2″ x 5′ (50 mm x 1.2 m) | ||
2″ x 6′ (50 mm x 1.8 m) | ||
2″ x 12′ (50 mm x 3.6 m) | ||
3″ x 9′ (75 mm x 2.7 m) | ||
4″ x 12′ (100 mm x 3.6 m) | ||
1 unit of Seal Stic Quick Cure Epoxy | ||
1 pair of latex gloves | ||
Operating instruction |

APPLICABLE MATERIAL:
• Steel
• Copper
• Aluminium
• Galvanized steel
• PVC
• CPVC
• Stainless steel
• Polyethylene
• Polypropylene
• Cast-iron
• Concrete
• FRP/GRE
CURING TIME:
• 30 minutes at 30 °C (86 °F)
Heat may be applied to decrease curing time.
Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.
CHEMICAL RESISTANCE:
• Oil
• Water (drinking water, wastewater, steam)
• Solvents (acetone, toluene, MEK, ethyl alcohol)
• Mild acids (hydrochloric acid, sulfuric acid) and alkalis
• Chemical (ethylene glycol, xylenes, ammonia)
• Hydrocarbons
• Bases
• Slurries
• Fuels (petroleum, diesels, gasoline)
• Gases (LNG, LPG)
• Organic salts
TECHNICAL DATA:
Pressure tested | : | 1/2″ (15 mm) steel pipe with 1/8″ (3 mm) hole when repaired with Wrap Seal withstands 4000 psi (281 kg/cm2) |
1/2″ (15 mm) steel pipe with 1/2″ (13 mm) hole when repaired with Wrap Seal withstands 600 psi (42 kg/cm2) | ||
Tensile strength | : | 3920 psi (276 kg/cm2) |
Bond strength | : | 230 psi (16 kg/cm2) |
Bond strength | : | 230 psi (16 kg/cm2) |
Tensile elongation | : | 1.2 % ± 0.7 % |
Compression strength | : | 13750 ± 530 psi (967 ± 37 kg/cm2) |
Yield strength | : | 2260 psi (159 kg/cm2) |
Cured hardness | : | 82 Shore D |
WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:
1

Stop the pipe flow
2

Roughen the area to be repaired
3

Knead the Seal Stic
4

Apply the Seal Stic to fill in holes or crack of the damaged or leak area
5

Immerse the Wrap Seal Fiberglass Tape into water
6

Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible, using the entire roll
7

Discard the plastic tube at the end of the roll
8

Wet gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
9

Continue to polish the wrap until all bubbling has stopped.
Repair completed with smooth and hard ivory appearance
Manufactured By SealXpert Products www.sealxpert.com © Copyright 2004